AD8552ARZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8552 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Operating Supply Current | 1.95mA |
| Quiescent Current | 975μA |
| Slew Rate | 0.4V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 5μV |
| Gain Bandwidth Product | 1.5MHz |
| Unity Gain BW-Nom | 1500 kHz |
| Voltage Gain | 145dB |
| Average Bias Current-Max (IIB) | 0.004μA |
| Power Supply Rejection Ratio (PSRR) | 115dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Wideband | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8552ARZ-REEL Overview
Packaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. A Zero-Drift-type buffer amplifier is shown here. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. During the past two weeks, there have been close to 8 terminations. Buffer amplifier has a total of 8 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. Instrumentation amplifier is a part of Operational Amplifier. 8 pins are included on the operational amplifiers. The input offset voltage is 5μV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . You can run this op amp ic on 1.95mA . There should be no change in the voltage gain. There are a total of 2 channels available on the op amps. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 3V. For packing the buffer amplifier, the TAPE AND REEL-axis is adopted. The quiescent current is 975μA.
AD8552ARZ-REEL Features
8 Pins
supply voltage of 5V
145dB voltage gain
Output Type: Rail-to-Rail
AD8552ARZ-REEL Applications
There are a lot of Analog Devices Inc. AD8552ARZ-REEL Instrumentational OP Amps applications.
- Signal transformation
- earphone
- Communication device
- High/low-pass filter circuit
- Exponential operation circuits
- Automotive sensors
- pH (acidity)
- Weak signal detection
- Gaming industry
- Inverse/same-phase proportional circuit
