AD8567ACPZ-R2
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8567 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 4 |
| Operating Supply Current | 700μA |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 80nA |
| Voltage - Supply, Single/Dual (±) | 4.5V~16V |
| Output Current per Channel | 35mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 5MHz |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 80dB |
| Average Bias Current-Max (IIB) | 0.8μA |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.6μA |
| Programmable Power | NO |
| Input Capacitance | 1pF |
| Input Voltage Noise Density | 26nV/sqrt Hz |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8567ACPZ-R2 Overview
Packaging for the buffer amplifier is in the form of a 16-VQFN Exposed Pad, CSP case. Buffer amps of this type are called General Purpose-types. The op amp is delivered to you in a Tape & Reel (TR) case. The number of terminations is approaching the 16 mark. In this case, there are 16 pins on the board. Please take in mind that this instrumentation amplifier should be run at 4.5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. Linear amplifier includes 16 pins. Op amp ic rates 2mV for input offset voltage. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~85°C . A supply current of 700μA can be used to operate this linear amplifier. Op amp is a member of the 80dB's 80dB family. Op amp ic has 4 channels. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
AD8567ACPZ-R2 Features
16 Pins
supply voltage of 4.5V
80dB voltage gain
Output Type: Rail-to-Rail
AD8567ACPZ-R2 Applications
There are a lot of Analog Devices Inc. AD8567ACPZ-R2 Instrumentational OP Amps applications.
- Television broadcasting equipment
- Measurements of Wheatstone bridge
- Vehicle electronics
- Signal filtering
- Power transmission
- Test equipment
- Fast A/D and D/A converters
- Digital cameras
- Active probe
- Portable electronic products powered by batteries
