AD8574TRU-EP
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | AD8574 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | 2.7/5V |
| Number of Channels | 4 |
| Operating Supply Current | 3.9mA |
| Quiescent Current | 975μA |
| Slew Rate | 0.4V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 140 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 5μV |
| Gain Bandwidth Product | 1.5MHz |
| Unity Gain BW-Nom | 1500 kHz |
| Voltage Gain | 145dB |
| Average Bias Current-Max (IIB) | 0.0015μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | NO |
| Wideband | NO |
| Input Voltage Noise Density | 51nV/sqrt Hz |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD8574TRU-EP Overview
Packaged in a 14-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. This is a Zero-Drift type op amp. There is a Tube case that is delivered with the instrumentation amplifiers. It is estimated that there will be 14 terminations in the next few months. A total of 14 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. To be specific, this instrumentation amplifier is a type of Operational Amplifier. A total of 14 pins are present on the instrumentation amplifier. There is an input offset voltage of 5μV for this buffer op amp. For this electronic part, it is recommended that you mount it with type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -55°C~125°C . You can run this op amp ic on 3.9mA . You should keep the voltage gain at 145dB for the time being. There are a total of 4 channels available on the op amps. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 3V. The current is quiescent at 975μA.
AD8574TRU-EP Features
14 Pins
supply voltage of 5V
145dB voltage gain
Output Type: Rail-to-Rail
AD8574TRU-EP Applications
There are a lot of Analog Devices Inc. AD8574TRU-EP Instrumentational OP Amps applications.
- Automotive sensors
- Industrial applications including automation
- Vehicle electronics
- Information processing
- Non-polarized electrodes
- Computer workstations
- RF cable systems
- Portable docking station
- Medical imaging
- Commercial audio systems
