AD8601ARTZ-R2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | DigiTrim® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8601 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 1.2mA |
| Quiescent Current | 1.2mA |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 8.4MHz |
| Unity Gain BW-Nom | 8200 kHz |
| Voltage Gain | 98.06dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 80μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Input Voltage Noise Density | 33nV/sqrt Hz |
| Height | 1.15mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8601ARTZ-R2 Overview
There is a SC-74A, SOT-753 case in which the instrumentation amplifier is packaged. Op amps are General Purpose types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There have been a total of 5 terminations over the past year. A total of 5 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 3V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. An 5-pin op amp ic is included in the package. As far as the input offset voltage is concerned, linear amplifier rates at 500μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing an 1.2mA supply current, this operational amplifier ics can be operated. 98.06dB should remain the voltage gain. Op amp ic has 1 channels. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. The operating supply voltage of the buffer op amp is rated at 5V. For packing the buffer amplifier, the TR-axis is adopted. As the name implies, DigiTrim? refers to the series of the buffer op amp. The quiescent current is 1.2mA.
AD8601ARTZ-R2 Features
5 Pins
supply voltage of 3V
98.06dB voltage gain
Output Type: Rail-to-Rail
AD8601ARTZ-R2 Applications
There are a lot of Analog Devices Inc. AD8601ARTZ-R2 Instrumentational OP Amps applications.
- Micro signal measurement
- Car stereo
- Division circuits
- Non-polarized electrodes
- Blood pressure sensors
- Semiconductor detectors
- High speed sample
- Biopotential
- Logarithmic operation circuits
- Proportional counter tubes
