AD8602DRMZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | DigiTrim® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8602 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Operating Supply Current | 2.4mA |
| Quiescent Current | 1.2mA |
| Supply Current-Max | 3mA |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 8.4MHz |
| Unity Gain BW-Nom | 8200 kHz |
| Voltage Gain | 95.56dB |
| Average Bias Current-Max (IIB) | 0.001μA |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1.3mV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Input Voltage Noise Density | 33nV/sqrt Hz |
| Height | 950μm |
| Length | 3.2mm |
| Width | 3.2mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8602DRMZ-REEL Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. Buffer amplifier has a total of 8 pins. This linear amplifier should be powered by an 3V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. 8 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 500μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. The buffer amplifier is capable of operating from a supply current of 2.4mA . Maintain 95.56dB as the voltage gain. 2 channels are available on the instrumentation amplifier. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. The DigiTrim? stands for the buffer op amp's serial number. Currently, linear amplifier is operating with a quiescent current of 1.2mA.
AD8602DRMZ-REEL Features
8 Pins
supply voltage of 3V
95.56dB voltage gain
Output Type: Rail-to-Rail
AD8602DRMZ-REEL Applications
There are a lot of Analog Devices Inc. AD8602DRMZ-REEL Instrumentational OP Amps applications.
- Multimedia playback equipment
- Automation control systems
- High/low-pass filter circuit
- Voltage regulation circuit
- Subtraction operation circuits
- Comparator
- Inverse/same-phase proportional circuit
- Proportional counter tubes
- Instrumentation
- MP3
