AD8603AUJZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8603 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Operating Supply Current | 50μA |
| Quiescent Current | 50μA |
| Supply Current-Max | 0.06mA |
| Slew Rate | 0.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5V ±0.9V~2.5V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 300μV |
| Bandwidth | 400 kHz |
| Unity Gain BW-Nom | 385 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 12μV |
| Settling Time | 23 μs |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Input Capacitance | 2.5pF |
| Input Voltage Noise Density | 25nV/sqrt Hz |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8603AUJZ-REEL7 Overview
In the package, you will find a SOT-23-5 Thin, TSOT-23-5-case to contain the op amp ic. Op amps are General Purpose types of amplifier on the chip. Linear amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 5 terminations in the next few months. In this case, there are 5 pins on the board. It would be helpful if you could remember that this op amp ic should be powered by an 1.8V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. An 5-pin op amp ic is included in the package. There is an input offset voltage of 300μV for this buffer op amp. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, this op amp functions well at -40°C~125°C. A supply current of 50μA can be used to operate this linear amplifier. 120dB should be the voltage gain. On the buffer amps, there are 1 channels that can be used. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 3V. The instrumentation amplifier is packed in the form of TAPE AND REEL. There is an 50μA quiescent current running through op amp ic.
AD8603AUJZ-REEL7 Features
5 Pins
supply voltage of 1.8V
120dB voltage gain
Output Type: Rail-to-Rail
AD8603AUJZ-REEL7 Applications
There are a lot of Analog Devices Inc. AD8603AUJZ-REEL7 Instrumentational OP Amps applications.
- Signal operation
- Communication
- Non-polarized electrodes
- Multimedia playback equipment
- Thermocouples
- Radiation thermometry transducers
- Band-stop filter
- Signal transformation
- Automatic control
- Band-pass filter
