AD8604DRZ
| Parameters | |
|---|---|
| Average Bias Current-Max (IIB) | 0.001μA |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1.3mV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Input Voltage Noise Density | 33nV/sqrt Hz |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8604 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Operating Supply Current | 4.8mA |
| Quiescent Current | 1.2mA |
| Supply Current-Max | 6mA |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 600μV |
| Bandwidth | 8.4MHz |
| Unity Gain BW-Nom | 8200 kHz |
| Voltage Gain | 95.56dB |
AD8604DRZ Overview
It is packaged in an 14-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp ic of the General Purpose type. Instrumentation amplifier is delivered in a Tube case. There is a growing number of terminations approaching the number of 14. In total, there are 14 pins on this op amp ic. Please take in mind that op amp should be run at 3V. It should be noted that this op amp is a type of Operational Amplifier device. The op amp ic has an array of 14 pins on it. In terms of the input offset voltage, instrumentation amplifier rates at 600μV. Surface Mount is the recommended mounting type for this linear amplifier. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. A supply current of 4.8mA can be used to operate this linear amplifier. Keeping the voltage gain at 95.56dB is the best course of action. The op amp ic has 4 channels on it. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 5V voltage. Currently, linear amplifier is operating with a quiescent current of 1.2mA.
AD8604DRZ Features
14 Pins
supply voltage of 3V
95.56dB voltage gain
Output Type: Rail-to-Rail
AD8604DRZ Applications
There are a lot of Analog Devices Inc. AD8604DRZ Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Comparator
- Wireless base stations
- Scintillation detectors
- Hand-held batteries
- Exponential operation circuits
- Television
- ECG equipment
- Polarized electrodes
- Tablets
