AD8605ARTZ-R2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | DigiTrim® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8605 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 1mA |
| Max Supply Current | 1.2mA |
| Quiescent Current | 1.2mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 300μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 80μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Input Capacitance | 8.8pF |
| Input Voltage Noise Density | 8nV/sqrt Hz |
| Height | 1.15mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8605ARTZ-R2 Overview
There is a SC-74A, SOT-753 case in which the instrumentation amplifier is packaged. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. We are approaching the 5h termination of the year. In total, there are 5 pins on this op amp ic. This linear amplifier should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. There are 5 pins on this chip. Op amp rates 300μV as input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . An 1mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. There are 1 channels on the operational amplifiers. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of the buffer op amp is rated at 5V. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. Buffer op amp series numbers are indicated by the DigiTrim?. 1.2mA quiescent currents are flowing through buffer op amp.
AD8605ARTZ-R2 Features
5 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
AD8605ARTZ-R2 Applications
There are a lot of Analog Devices Inc. AD8605ARTZ-R2 Instrumentational OP Amps applications.
- Scintillation detectors
- Television
- Band-pass filter
- Instrumentation
- Multimedia playback equipment
- Voltage regulation circuit
- Precision measurement
- Automation control systems
- Portable docking station
- Signal operation
