AD8606ARM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | DigiTrim® |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8606 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 2.4mA |
| Quiescent Current | 1.2mA |
| Supply Current-Max | 3mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 300μV |
| Gain Bandwidth Product | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 120dB |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 80μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Programmable Power | NO |
| Input Capacitance | 8.8pF |
| Wideband | NO |
| Input Voltage Noise Density | 8nV/sqrt Hz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD8606ARM-REEL Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case package that contains the instrumentation amplifiers. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. In recent months, the number of terminations has approached 8. There are a total of 8 pins on this op amp. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. In total, the buffer amplifier consists of 8 pins. There is an input offset voltage of 300μV for this buffer op amp. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . You can run this op amp ic on 2.4mA . It is recommended to keep the voltage gain at 120dB at all times. As far as the device is concerned, buffer amplifier has 2 channels. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. TAPE AND REEL is adopted to pack the instrumentation amplifier. DigiTrim? corresponds to linear amplifier's series. There is a quiescent current of 1.2mA in this operational amplifier circuit.
AD8606ARM-REEL Features
8 Pins
supply voltage of 5V
120dB voltage gain
Output Type: Rail-to-Rail
AD8606ARM-REEL Applications
There are a lot of Analog Devices Inc. AD8606ARM-REEL Instrumentational OP Amps applications.
- Ultrasound transducers
- RF cable systems
- Exponential operation circuits
- Inverse/same-phase proportional circuit
- Differentiator circuits
- Active probe
- Power generator
- Comparator
- Signal transformation
- Communication device
