AD8607ARM-REEL
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8607 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Operating Supply Current | 40μA |
| Quiescent Current | 50μA |
| Slew Rate | 0.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5V ±0.9V~2.5V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 12μV |
| Gain Bandwidth Product | 400kHz |
| Unity Gain BW-Nom | 385 kHz |
| Voltage Gain | 113.06dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Input Capacitance | 2.5pF |
| Input Voltage Noise Density | 25nV/sqrt Hz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
AD8607ARM-REEL Overview
A 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case is used to package the op amp. An op amp of this type is a General Purpose-type. Linear amplifier is delivered in a Tape & Reel (TR) case. There is a growing number of terminations approaching the number of 8. Buffer amplifier has a total of 8 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 1.8V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are included on the operational amplifiers. The input offset voltage is 12μV. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . It is possible to operate this buffer amplifier from a supply current of 40μA . It is recommended to keep the voltage gain at 113.06dB at all times. There are 2 channels on the operational amplifiers. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The operating supply voltage of instrumentation amplifier is rated 3V voltage. The instrumentation amplifier is packed in the form of TAPE AND REEL. There is a quiescent current of 50μA in this operational amplifier circuit.
AD8607ARM-REEL Features
8 Pins
supply voltage of 1.8V
113.06dB voltage gain
Output Type: Rail-to-Rail
AD8607ARM-REEL Applications
There are a lot of Analog Devices Inc. AD8607ARM-REEL Instrumentational OP Amps applications.
- Image computer boards
- High-frequency data acquisition systems
- Exponential operation circuits
- Signal operation
- Communication device
- Proportional counter tubes
- Addition operation circuits
- ECG equipment
- Scintillation detectors
- Comparator
