AD8610ARZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8610 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 3.5mA |
| Quiescent Current | 3.5mA |
| Supply Current-Max | 4mA |
| Slew Rate | 60V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | ±5V~13V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 100μV |
| Gain Bandwidth Product | 25MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 25000 kHz |
| Voltage Gain | 105.11dB |
| Average Bias Current-Max (IIB) | 0.0025μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 85μV |
| Settling Time | 600 ns |
| Low-Bias | YES |
| Input Capacitance | 15pF |
| Input Voltage Noise Density | 6nV/sqrt Hz |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8610ARZ-REEL Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. J-FET-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be 8 terminations in the next few months. Buffer amplifier has a total of 8 pins on it. Please take in mind that this instrumentation amplifier should be run at 5V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. Op amp ic rates 100μV for input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Operational amplifier can operate supply current at 3.5mA. Keeping the voltage gain at 105.11dB is the best course of action. 1 channels are available on the instrumentation amplifier. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. There is an 3.5mA quiescent current in linear amplifier.
AD8610ARZ-REEL Features
8 Pins
supply voltage of 5V
105.11dB voltage gain
AD8610ARZ-REEL Applications
There are a lot of Analog Devices Inc. AD8610ARZ-REEL Instrumentational OP Amps applications.
- Communication
- Band-stop filter
- Weak signal detection
- High speed sample
- Biopotential
- Medical instruments
- Multiplication circuits
- Video amplifiers
- Measurements of Wheatstone bridge
- Fast A/D and D/A converters
