AD8613AUJZ-R2
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8613 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Operating Supply Current | 38μA |
| Quiescent Current | 38μA |
| Slew Rate | 0.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5V ±0.9V~2.5V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 400μV |
| Bandwidth | 400 kHz |
| Unity Gain BW-Nom | 350 kHz |
| Voltage Gain | 113.98dB |
| Average Bias Current-Max (IIB) | 0.00078μA |
| Power Supply Rejection Ratio (PSRR) | 67dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Programmable Power | NO |
| Input Capacitance | 2.5pF |
| Input Voltage Noise Density | 25nV/sqrt Hz |
| Height | 900μm |
| Length | 2.9mm |
| Width | 1.6mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8613AUJZ-R2 Overview
The linear amplifier is packaged in a SOT-23-5 Thin, TSOT-23-5 case. The instrumentation amplifier in this picture is of the General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. We are approaching the 5h termination of the year. A total of 5 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 5V battery. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. In total, the buffer amplifier consists of 5 pins. Op amp rates 400μV as input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. Regarding the operating temperature of this device, instrumentation amplifier performs well at a temperature of -40°C~125°C . The buffer amplifier is capable of operating from a supply current of 38μA . Op amp is a member of the 113.98dB's 113.98dB family. Buffer op amp is equipped with 1 channels on the device. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of the buffer op amp is rated at 3V. The linear amplifier is packaged by using a TAPE AND REEL axis. There is an 38μA quiescent current in linear amplifier.
AD8613AUJZ-R2 Features
5 Pins
supply voltage of 5V
113.98dB voltage gain
Output Type: Rail-to-Rail
AD8613AUJZ-R2 Applications
There are a lot of Analog Devices Inc. AD8613AUJZ-R2 Instrumentational OP Amps applications.
- Hand-held batteries
- Ultrasound transducers
- Broadcasting
- Automatic control
- Television
- Multiplication circuits
- RF cable systems
- Digital cameras
- Logarithmic operation circuits
- Active probe
