AD8614ARTZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -20°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 18V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8614 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 1.1mA |
| Quiescent Current | 1.1mA |
| Slew Rate | 7.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 75 dB |
| Current - Input Bias | 80nA |
| Voltage - Supply, Single/Dual (±) | 5V~18V |
| Output Current per Channel | 70mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Bandwidth | 5.5MHz |
| Unity Gain BW-Nom | 5500 kHz |
| Voltage Gain | 103.52dB |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 20V |
| Voltage - Input Offset | 1mV |
| Settling Time | 3 μs |
| Low-Bias | NO |
| Micropower | NO |
| Max Frequency | 10kHz |
| Bias Current-Max (IIB) @25C | 0.4μA |
| Programmable Power | NO |
| Input Voltage Noise Density | 12nV/sqrt Hz |
| Height | 1.3mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8614ARTZ-REEL7 Overview
It is packaged in an SC-74A, SOT-753-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. There have been a total of 5 terminations over the past year. Buffer amplifier has a total of 5 pins on it. It would be helpful if you could remember that this op amp ic should be powered by an 18V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. A total of 5 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 2.5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -20°C~85°C as far as operating temperature is concerned. An 1.1mA volt supply current is needed for this linear amplifier to operate. The voltage gain should stay at 103.52dB. There are 1 channels on the operational amplifiers. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. Buffer amplifier has a quiescent current of 1.1mA.
AD8614ARTZ-REEL7 Features
5 Pins
supply voltage of 18V
103.52dB voltage gain
Output Type: Rail-to-Rail
AD8614ARTZ-REEL7 Applications
There are a lot of Analog Devices Inc. AD8614ARTZ-REEL7 Instrumentational OP Amps applications.
- Professional videography
- Voltage regulation circuit
- Video conversion and routing
- Band-pass filter
- Signal filtering
- Comparator
- pH (acidity)
- Signal amplification
- Subtraction operation circuits
- Radiation thermometry transducers
