AD8618ARZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | DigiTrim® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8618 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | 2.7/5V |
| Number of Channels | 4 |
| Operating Supply Current | 8mA |
| Quiescent Current | 2mA |
| Supply Current-Max | 10mA |
| Slew Rate | 12V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 150mA |
| Input Offset Voltage (Vos) | 60μV |
| Gain Bandwidth Product | 24MHz |
| Unity Gain BW-Nom | 23000 kHz |
| Voltage Gain | 123.52dB |
| Average Bias Current-Max (IIB) | 0.00055μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 23μV |
| Settling Time | 500 ns |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Input Capacitance | 10pF |
| Input Voltage Noise Density | 10nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8618ARZ-REEL7 Overview
There is a 14-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. A General Purpose-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. It is estimated that there will be 14 terminations in the next few months. The total number of pins on linear amplifier is 14. It would be helpful if you could remember that this op amp ic should be powered by an 2.7V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The buffer op amp includes 14 pins. With regard to input offset voltage, instrumentation amplifier is rated at 60μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . Operational amplifier can operate supply current at 8mA. 123.52dB should be the voltage gain. Instrumentation amplifier has 4 channels on it. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of the buffer op amp is rated at 3V. It is used TAPE AND REEL to pack the op amps. DigiTrim? corresponds to the op amp's series. Buffer amplifier has a quiescent current of 2mA.
AD8618ARZ-REEL7 Features
14 Pins
supply voltage of 2.7V
123.52dB voltage gain
Output Type: Rail-to-Rail
AD8618ARZ-REEL7 Applications
There are a lot of Analog Devices Inc. AD8618ARZ-REEL7 Instrumentational OP Amps applications.
- single/dual op amp sum and difference circuits
- Communication
- Blood pressure sensors
- Television
- Weak signal detection
- Image computer boards
- Power control
- Power transmission
- Test equipment
- Commercial audio systems
