AD8628ARTZ-R2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8628 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Operating Supply Current | 1.1mA |
| Quiescent Current | 1.1mA |
| Slew Rate | 1V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 140 dB |
| Current - Input Bias | 30pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5V ±1.35V~2.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 5μV |
| Bandwidth | 2.5MHz |
| Unity Gain BW-Nom | 2500 kHz |
| Voltage Gain | 145dB |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1μV |
| Gain | 120 dB |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Input Capacitance | 10pF |
| Height | 1.15mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8628ARTZ-R2 Overview
The linear amplifier is packaged in a SC-74A, SOT-753 case which makes it easy for the consumer to handle. A Zero-Drift-type buffer amplifier is shown here. Linear amplifier is delivered in a Cut Tape (CT) case. In recent months, the number of terminations has approached 5. In this case, there are 5 pins on the board. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 5 pins are included on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 5μV. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 1.1mA, this op amp ic can operate. Voltage gain should remain at 145dB. There are a total of 1 channels available on the op amps. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 3V. The linear amplifier is packaged by using a TAPE AND REEL axis. Buffer amplifier has a quiescent current of 1.1mA.
AD8628ARTZ-R2 Features
5 Pins
supply voltage of 5V
145dB voltage gain
Output Type: Rail-to-Rail
AD8628ARTZ-R2 Applications
There are a lot of Analog Devices Inc. AD8628ARTZ-R2 Instrumentational OP Amps applications.
- Medical instruments
- Multimedia playback equipment
- Vehicle electronics
- Switching amplifier
- Video amplifiers
- Portable docking station
- Radiation thermometry transducers
- Measurements of Wheatstone bridge
- Voltage regulation circuit
- Cinema or auditorium audio system
