AD8630ARUZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8630 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Power Supplies | +-1.35/+-2.5/2.7/5V |
| Number of Channels | 4 |
| Operating Supply Current | 4.4mA |
| Quiescent Current | 1.1mA |
| Slew Rate | 1V/μs |
| Architecture | CHOPPER-STAB |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 140 dB |
| Current - Input Bias | 100pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5V ±1.35V~2.5V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 2.5μV |
| Gain Bandwidth Product | 2.5MHz |
| Unity Gain BW-Nom | 2500 kHz |
| Voltage Gain | 145dB |
| Average Bias Current-Max (IIB) | 0.0015μA |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0003μA |
| Programmable Power | NO |
| Input Capacitance | 10pF |
| Wideband | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8630ARUZ-REEL Overview
Packaged in a 14-TSSOP (0.173, 4.40mm Width) case, the buffer op amp is ready to use. Op amps are Zero-Drift types of amplifier on the chip. Linear amplifier is delivered in a Tape & Reel (TR) case. A total of 14 terminations have been reported in the past few weeks. In this case, there are 14 pins on the board. Please take in mind that op amp should be run at 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. In total, the buffer amplifier consists of 14 pins. Op amp ic rates 2.5μV for input offset voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . This op amp can operate from a supply current at 4.4mA. Voltage gain should remain at 145dB. There are 4 channels on the operational amplifiers. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. The operating supply voltage of the buffer op amp is rated at 3V. TAPE AND REEL is adopted to pack the instrumentation amplifier. Buffer amplifier has a quiescent current of 1.1mA.
AD8630ARUZ-REEL Features
14 Pins
supply voltage of 5V
145dB voltage gain
Output Type: Rail-to-Rail
AD8630ARUZ-REEL Applications
There are a lot of Analog Devices Inc. AD8630ARUZ-REEL Instrumentational OP Amps applications.
- Ultrasound transducers
- High speed sample
- Automatic control
- Strain gauges
- Radiation thermometry transducers
- Vehicle electronics
- earphone
- Cinema or auditorium audio system
- Navigation
- Proportional counter tubes
