AD8638ARZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8638 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Operating Supply Current | 1.5mA |
| Quiescent Current | 1.5mA |
| Slew Rate | 2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | Zero-Drift |
| Common Mode Rejection Ratio | 127 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 5V~16V ±2.5V~8V |
| Output Current per Channel | 37mA |
| Input Offset Voltage (Vos) | 9μV |
| Bandwidth | 1.5MHz |
| Unity Gain BW-Nom | 1350 kHz |
| Voltage Gain | 136dB |
| Power Supply Rejection Ratio (PSRR) | 127dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 3μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000075μA |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Input Voltage Noise Density | 60nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8638ARZ Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. An op amp of this type is a Zero-Drift-type. A Tube case is used for delivering the op amp. There is a growing number of terminations approaching the number of 8. The pins on this board total to 8 in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 8 pins are available on the instrumentation amplifier. The input offset voltage is 9μV. The mounting type that is recommended for this electrical part is Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~125°C. An 1.5mA volt supply current is needed for this linear amplifier to operate. Voltage gain should remain at 136dB. On the buffer amps, there are 1 channels that can be used. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of the buffer op amp is rated at 15V. There is an 1.5mA quiescent current running through op amp ic.
AD8638ARZ Features
8 Pins
supply voltage of 5V
136dB voltage gain
Output Type: Rail-to-Rail
AD8638ARZ Applications
There are a lot of Analog Devices Inc. AD8638ARZ Instrumentational OP Amps applications.
- Signal operation
- Medical instruments
- Voltage regulation circuit
- Digital cameras
- Proportional operation circuits
- Tablets
- single/dual op amp sum and difference circuits
- Multimedia playback equipment
- Integrator circuits
- Vehicle electronics
