AD8642ARMZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8642 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 24V |
| Number of Channels | 2 |
| Operating Supply Current | 580μA |
| Quiescent Current | 290μA |
| Supply Current-Max | 0.66mA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 107 dB |
| Current - Input Bias | 0.25pA |
| Voltage - Supply, Single/Dual (±) | 5V~26V ±2.5V~13V |
| Output Current per Channel | 12mA |
| Input Offset Voltage (Vos) | 750μV |
| Bandwidth | 3.5MHz |
| Neg Supply Voltage-Nom (Vsup) | -13V |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 102.92dB |
| Power Supply Rejection Ratio (PSRR) | 107dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 13.65V |
| Voltage - Input Offset | 70μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Input Voltage Noise Density | 28.5nV/sqrt Hz |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8642ARMZ Overview
Packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. Op amps are J-FET types of amplifier on the chip. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. The number of terminations approaches 8. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 13V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. An 8-pin op amp ic is included in the package. The input offset voltage is 750μV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . Operational amplifier can operate supply current at 580μA. There should be no change in the voltage gain at 102.92dB. There are a total of 2 channels available on the op amps. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of the buffer op amp is rated at 24V. The current is quiescent at 290μA.
AD8642ARMZ Features
8 Pins
supply voltage of 13V
102.92dB voltage gain
Output Type: Rail-to-Rail
AD8642ARMZ Applications
There are a lot of Analog Devices Inc. AD8642ARMZ Instrumentational OP Amps applications.
- High-frequency data acquisition systems
- Signal amplification
- Comparator
- Active probe
- Automation control systems
- Non-polarized electrodes
- Industrial applications including automation
- Fission chambers
- Signal operation
- Power control
