AD8642ARZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 13V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8642 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 2 |
| Operating Supply Current | 580μA |
| Quiescent Current | 290μA |
| Supply Current-Max | 0.66mA |
| Slew Rate | 3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 107 dB |
| Current - Input Bias | 0.25pA |
| Voltage - Supply, Single/Dual (±) | 5V~26V ±2.5V~13V |
| Output Current per Channel | 12mA |
| Input Offset Voltage (Vos) | 750μV |
| Gain Bandwidth Product | 3.5MHz |
| Neg Supply Voltage-Nom (Vsup) | -13V |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 102.92dB |
| Power Supply Rejection Ratio (PSRR) | 107dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 13.65V |
| Voltage - Input Offset | 70μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Neg Supply Voltage-Max (Vsup) | -13.65V |
| Input Voltage Noise Density | 28.5nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8642ARZ-REEL Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. J-FET-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations is approaching the 8 mark. Linear amplifier has a total of 8 pins. I would like to remind you that this buffer op amp should be powered by an 13V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. It has 8 pins that make up the linear amplifier. As far as the input offset voltage is concerned, linear amplifier rates at 750μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. In order for this instrumentation amplifier to operate, the supply current needs to be between 580μA and 10 . Maintain 102.92dB as the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. As a result, linear amplifier's quiescent current is 290μA.
AD8642ARZ-REEL Features
8 Pins
supply voltage of 13V
102.92dB voltage gain
Output Type: Rail-to-Rail
AD8642ARZ-REEL Applications
There are a lot of Analog Devices Inc. AD8642ARZ-REEL Instrumentational OP Amps applications.
- Radar
- Integrator circuits
- Mobile phone
- Proportional operation circuits
- Multimedia playback equipment
- Television broadcasting equipment
- Displayers for aircraft and air transportation control systems
- Active probe
- Home audio systems
- Test equipment
