Parameters |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
8-VFDFN Exposed Pad, CSP |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
Series |
DigiTrim® |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Discontinued |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Packing Method |
TAPE AND REEL |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
AD8661 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Output Type |
Rail-to-Rail |
Number of Channels |
1 |
Operating Supply Current |
1.25mA |
Quiescent Current |
1.4mA |
Slew Rate |
3.5V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
110 dB |
Current - Input Bias |
0.3pA |
Voltage - Supply, Single/Dual (±) |
5V~16V |
Output Current per Channel |
140mA |
Input Offset Voltage (Vos) |
30μV |
Bandwidth |
4MHz |
Unity Gain BW-Nom |
4000 kHz |
Voltage Gain |
107.6dB |
Average Bias Current-Max (IIB) |
0.00005μA |
Power Supply Rejection Ratio (PSRR) |
110dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Voltage - Input Offset |
50μV |
Low-Bias |
YES |
Micropower |
NO |
Programmable Power |
NO |
Input Voltage Noise Density |
12nV/sqrt Hz |
Height |
850μm |
Length |
3mm |
Width |
3mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
AD8661ACPZ-R2 Overview
A 8-VFDFN Exposed Pad, CSP case is used to package the op amp. There are two types of operational amplifiers in this circuit. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. There are 8 pins on this chip. With regards to the offset voltage of the input, buffer amplifier is rated at 30μV. This electronic part is recommended for mounting type Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~85°C . You can run this op amp ic on 1.25mA . Op amp is a member of the 107.6dB's 107.6dB family. 1 channels are available on the instrumentation amplifier. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The instrumentation amplifier is packed in the form of TAPE AND REEL. The DigiTrim? indicates the series number of the op amp. There is an 1.4mA quiescent current in linear amplifier.
AD8661ACPZ-R2 Features
8 Pins
supply voltage of 5V
107.6dB voltage gain
Output Type: Rail-to-Rail
AD8661ACPZ-R2 Applications
There are a lot of Analog Devices Inc. AD8661ACPZ-R2 Instrumentational OP Amps applications.
- Thermocouples
- Active probe
- Signal transformation
- Signal amplification
- Test equipment
- Digital cameras
- Band-pass filter
- Information processing
- Division circuits
- Exponential operation circuits