AD8663ARZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | DigiTrim® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8663 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 285μA |
| Quiescent Current | 285μA |
| Slew Rate | 0.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 109 dB |
| Current - Input Bias | 0.3pA |
| Voltage - Supply, Single/Dual (±) | 5V~16V ±2.5V~8V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 300μV |
| Gain Bandwidth Product | 540kHz |
| Unity Gain BW-Nom | 520 kHz |
| Voltage Gain | 140dB |
| Power Supply Rejection Ratio (PSRR) | 105dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Voltage - Input Offset | 40μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Wideband | NO |
| Input Voltage Noise Density | 23nV/sqrt Hz |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8663ARZ-REEL Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. This is a General Purpose type op amp. The op amp is delivered to you in a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. In this case, there are 8 pins on the board. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are located on the operational amplifiers. As far as the input offset voltage is concerned, linear amplifier rates at 300μV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureThe buffer amplifier is capable of operating from a supply current of 285μA . It is recommended to keep the voltage gain at 140dB at all times. Buffer op amp is equipped with 1 channels on the device. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. The DigiTrim? stands for the buffer op amp's serial number. Buffer amplifier has a quiescent current of 285μA.
AD8663ARZ-REEL Features
8 Pins
supply voltage of 5V
140dB voltage gain
Output Type: Rail-to-Rail
AD8663ARZ-REEL Applications
There are a lot of Analog Devices Inc. AD8663ARZ-REEL Instrumentational OP Amps applications.
- Instrumentation
- Comparator
- Fission chambers
- Communication
- Test equipment
- Medical instruments
- RF cable systems
- Weighing systems
- Test and measurement instruments
- Proportional counter tubes
