AD8664ARZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | DigiTrim® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8664 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 15V |
| Power Supplies | +-2.5/+-8/5/16V |
| Number of Channels | 4 |
| Operating Supply Current | 6.2mA |
| Quiescent Current | 1.55mA |
| Supply Current-Max | 8mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 0.3pA |
| Voltage - Supply, Single/Dual (±) | 5V~16V |
| Output Current per Channel | 140mA |
| Input Offset Voltage (Vos) | 160μV |
| Bandwidth | 4MHz |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.85dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 50μV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Input Voltage Noise Density | 12nV/sqrt Hz |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8664ARZ Overview
There is a 14-SOIC (0.154, 3.90mm Width) case in which the instrumentation amplifier is packaged. A General Purpose-type buffer amplifier is shown here. The op amp is delivered to you in a Tube case. During the past two weeks, there have been close to 14 terminations. The pins on this board total to 14 in total. It is important to remember that this op amp should be operated at a voltage of 5V volts. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. An 14-pin op amp ic is included in the package. Regarding input offset voltage, op amp rates 160μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. This op amp can operate from a supply current at 6.2mA. The voltage gain should stay at 106.85dB. There are a total of 4 channels available on the op amps. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 15V voltage. Instrumentation amplifiers are numbered by their DigiTrim? series. There is an 1.55mA quiescent current running through op amp ic.
AD8664ARZ Features
14 Pins
supply voltage of 5V
106.85dB voltage gain
Output Type: Rail-to-Rail
AD8664ARZ Applications
There are a lot of Analog Devices Inc. AD8664ARZ Instrumentational OP Amps applications.
- Measurements of Wheatstone bridge
- Communication device
- Test and measurement instruments
- Automotive sensors
- Gaming industry
- RF cable systems
- Broadcasting
- Image computer boards
- Mobile phone
- Portable media players
