AD8665ARJZ-R2
| Parameters | |
|---|---|
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8665 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 1.15mA |
| Quiescent Current | 1.55mA |
| Supply Current-Max | 2mA |
| Min Input Voltage | 5V |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 0.2pA |
| Max Input Voltage | 16V |
| Voltage - Supply, Single/Dual (±) | 5V~16V ±2.5V~8V |
| Output Current per Channel | 140mA |
| Input Offset Voltage (Vos) | 600μV |
| Bandwidth | 4MHz |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 103.23dB |
| Power Supply Rejection Ratio (PSRR) | 98dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 10kHz |
| Programmable Power | NO |
| Input Voltage Noise Density | 10nV/sqrt Hz |
| Height | 1.3mm |
| Length | 3mm |
| Width | 1.7mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
AD8665ARJZ-R2 Overview
There is a SC-74A, SOT-753 case in which the instrumentation amplifier is packaged. Buffer amps of this type are called General Purpose-types. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. A total of 5 terminations have been reported in the past few weeks. A total of 5 pins are attached to buffer op amp. Please take in mind that this instrumentation amplifier should be run at 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. A total of 5 pins are present on the instrumentation amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 600μV. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. Using an 1.15mA supply current, this operational amplifier ics can be operated. There should be no change in the voltage gain at 103.23dB. Op amp ic has 1 channels. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps. 1.55mA quiescent currents are flowing through buffer op amp.
AD8665ARJZ-R2 Features
5 Pins
supply voltage of 5V
103.23dB voltage gain
Output Type: Rail-to-Rail
AD8665ARJZ-R2 Applications
There are a lot of Analog Devices Inc. AD8665ARJZ-R2 Instrumentational OP Amps applications.
- High gain DC amplifier
- Test equipment
- Computer workstations
- Measurements of Wheatstone bridge
- Industrial applications including automation
- Division circuits
- Micro signal measurement
- Instrumentation
- Polarized electrodes
- Ultrasound transducers
