AD8668WARUZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8668 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Number of Channels | 4 |
| Operating Supply Current | 6.2mA |
| Quiescent Current | 1.55mA |
| Slew Rate | 3.5V/μs |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 5V~16V ±2.5V~8V |
| Output Current per Channel | 140mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Gain Bandwidth Product | 4MHz |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 103.23dB |
| Average Bias Current-Max (IIB) | 0.00055μA |
| Power Supply Rejection Ratio (PSRR) | 115dB |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 600μV |
| Input Voltage Noise Density | 10nV/sqrt Hz |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8668WARUZ-R7 Overview
The linear amplifier is packaged in a 14-TSSOP (0.173, 4.40mm Width) case which makes it easy for the consumer to handle. Buffer amps of this type are called General Purpose-types. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be at least 14 terminations this year. A total of 14 pins are attached to buffer op amp. Please take in mind that this instrumentation amplifier should be run at 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. 14 pins are included on the operational amplifiers. Regarding input offset voltage, buffer amplifier rates 2.5mV voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. This op amp can operate from a supply current at 6.2mA. The voltage gain should stay at 103.23dB. 4 channels are available on the instrumentation amplifier. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. Automotive is the number that corresponds to the series of the buffer op amp. 1.55mA quiescent currents are flowing through buffer op amp.
AD8668WARUZ-R7 Features
14 Pins
supply voltage of 5V
103.23dB voltage gain
Output Type: Rail-to-Rail
AD8668WARUZ-R7 Applications
There are a lot of Analog Devices Inc. AD8668WARUZ-R7 Instrumentational OP Amps applications.
- Communication device
- Power control
- Signal transformation
- Exponential operation circuits
- pH (acidity)
- Multiplication circuits
- Mobile phone
- Inverse/same-phase proportional circuit
- Comparator
- Vehicle electronics
