AD8677ARZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | iPolar® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8677 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 1.3mA |
| Quiescent Current | 1.3mA |
| Slew Rate | 0.2V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 140 dB |
| Current - Input Bias | 200pA |
| Voltage - Supply, Single/Dual (±) | ±4V~18V |
| Output Current per Channel | 15mA |
| Input Offset Voltage (Vos) | 130μV |
| Bandwidth | 600 kHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 600 kHz |
| Voltage Gain | 140dB |
| Power Supply Rejection Ratio (PSRR) | 130dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 45μV |
| Gain | 115 dB |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Input Voltage Noise Density | 10nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8677ARZ Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. This is a General Purpose type op amp. A Tube case is used to deliver the buffer op amp. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are located on this board. Please take in mind that this instrumentation amplifier should be run at 5V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are located on the operational amplifiers. Op amp rates 130μV as input offset voltage. This electronic component is recommended to be mounted using the mounting type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using an 1.3mA supply current, this operational amplifier ics can be operated. The voltage gain should stay at 140dB. Instrumentation amplifier has 1 channels on it. In this case, iPolar? represents the instrumentation amplifiers' series number. There is an 1.3mA quiescent current running through op amp ic.
AD8677ARZ Features
8 Pins
supply voltage of 5V
140dB voltage gain
AD8677ARZ Applications
There are a lot of Analog Devices Inc. AD8677ARZ Instrumentational OP Amps applications.
- Multimedia playback equipment
- Communication device
- Band-pass filter
- Computer workstations
- Measurements of Wheatstone bridge
- RF cable systems
- Weak signal detection
- Power generator
- Micro signal measurement
- Gaming industry
