AD8691AUJZ-R2
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AD8691 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 950μA |
| Quiescent Current | 1.05mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 400μV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.00026μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Input Voltage Noise Density | 8nV/sqrt Hz |
| Height | 900μm |
| Length | 2.9mm |
| Width | 1.6mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8691AUJZ-R2 Overview
There is a SOT-23-5 Thin, TSOT-23-5 case package that contains the instrumentation amplifiers. A General Purpose-type buffer amplifier is shown here. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be at least 5 terminations this year. There are a total of 5 pins on this op amp. Please take in mind that op amp should be run at 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. The op amp ic has an array of 5 pins on it. In terms of input offset voltage, operational amplifier rates 400μV. This electronic part is recommended for mounting type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. It is possible to operate this buffer amplifier from a supply current of 950μA . 126.02dB should remain the voltage gain. There are 1 channels on the operational amplifiers. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. 1.05mA quiescent currents are flowing through buffer op amp.
AD8691AUJZ-R2 Features
5 Pins
supply voltage of 5V
126.02dB voltage gain
Output Type: Rail-to-Rail
AD8691AUJZ-R2 Applications
There are a lot of Analog Devices Inc. AD8691AUJZ-R2 Instrumentational OP Amps applications.
- Communication
- Signal amplification
- MP3
- Strain gauges
- Video computer boards
- Active probe
- Division circuits
- Comparator
- Vehicle electronics
- Tablets
