AD8691WAUJZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | AD8691 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 1.05mA |
| Quiescent Current | 1.05mA |
| Slew Rate | 5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 95 dB |
| Current - Input Bias | 200nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 10MHz |
| Unity Gain BW-Nom | 10000 kHz |
| Voltage Gain | 126.02dB |
| Average Bias Current-Max (IIB) | 0.00026μA |
| Power Supply Rejection Ratio (PSRR) | 95dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 400μV |
| Settling Time | 1 μs |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Input Voltage Noise Density | 8nV/sqrt Hz |
| Length | 2.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8691WAUJZ-R7 Overview
The linear amplifier is packaged in a SOT-23-5 Thin, TSOT-23-5 case. An op amp of this type is a General Purpose-type. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. During the past two weeks, there have been close to 5 terminations. There are a total of 5 pins on this op amp. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. To be specific, this instrumentation amplifier is a type of Operational Amplifier. 5 pins are located on the operational amplifiers. With regard to input offset voltage, instrumentation amplifier is rated at 2mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing an 1.05mA supply current, this operational amplifier ics can be operated. Voltage gain should remain at 126.02dB. Instrumentation amplifier has 1 channels on it. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method. Buffer op amp series numbers are indicated by the Automotive. There is a quiescent current of 1.05mA in this operational amplifier circuit.
AD8691WAUJZ-R7 Features
5 Pins
supply voltage of 5V
126.02dB voltage gain
Output Type: Rail-to-Rail
AD8691WAUJZ-R7 Applications
There are a lot of Analog Devices Inc. AD8691WAUJZ-R7 Instrumentational OP Amps applications.
- Subtraction operation circuits
- Strain gauges
- Television
- Computer workstations
- Automatic control
- Scintillation detectors
- Inverse/same-phase proportional circuit
- Division circuits
- E-book readers
- ECG equipment
