Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~125°C |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Subcategory |
Operational Amplifier |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
AD8692 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Output Type |
Rail-to-Rail |
Operating Supply Voltage |
5V |
Number of Channels |
2 |
Operating Supply Current |
2.1mA |
Quiescent Current |
1.05mA |
Slew Rate |
5V/μs |
Architecture |
VOLTAGE-FEEDBACK |
Amplifier Type |
General Purpose |
Common Mode Rejection Ratio |
90 dB |
Current - Input Bias |
0.2pA |
Voltage - Supply, Single/Dual (±) |
2.7V~5.5V ±1.35V~2.75V |
Output Current per Channel |
80mA |
Input Offset Voltage (Vos) |
2mV |
Bandwidth |
10MHz |
Unity Gain BW-Nom |
10000 kHz |
Voltage Gain |
126.02dB |
Power Supply Rejection Ratio (PSRR) |
95dB |
Low-Offset |
NO |
Frequency Compensation |
YES |
Supply Voltage Limit-Max |
6V |
Voltage - Input Offset |
400μV |
Low-Bias |
YES |
Micropower |
NO |
Bias Current-Max (IIB) @25C |
0.000001μA |
Programmable Power |
NO |
Input Voltage Noise Density |
8nV/sqrt Hz |
Height |
1.5mm |
Length |
5mm |
Width |
4mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
AD8692ARZ Overview
The linear amplifier is packaged in a 8-SOIC (0.154, 3.90mm Width) case which makes it easy for the consumer to handle. A General Purpose-type buffer amplifier is shown here. The op amp is delivered to you in a Tube case. The number of terminations approaches 8. The total number of pins on linear amplifier is 8. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. In total, the buffer amplifier consists of 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 2mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. An 2.1mA volt supply current is needed for this linear amplifier to operate. 126.02dB should remain the voltage gain. Instrumentation amplifier has 2 channels on it. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of instrumentation amplifier is rated 5V voltage. The quiescent current is 1.05mA.
AD8692ARZ Features
8 Pins
supply voltage of 5V
126.02dB voltage gain
Output Type: Rail-to-Rail
AD8692ARZ Applications
There are a lot of Analog Devices Inc. AD8692ARZ Instrumentational OP Amps applications.
- Polarized electrodes
- Signal transformation
- Video data acquisition
- Oscilloscopes
- Portable electronic products powered by batteries
- Signal amplification
- Vehicle electronics
- Strain gauges
- Proportional counter tubes
- Comparator