ADA4000-2ARMZ-RL
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADA4000 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 2 |
| Operating Supply Current | 3.3mA |
| Quiescent Current | 1.65mA |
| Supply Current-Max | 3.6mA |
| Slew Rate | 20V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | 8V~36V ±4V~18V |
| Output Current per Channel | 28mA |
| Input Offset Voltage (Vos) | 1.7mV |
| Gain Bandwidth Product | 5MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 5000 kHz |
| Voltage Gain | 114dB |
| Average Bias Current-Max (IIB) | 0.003μA |
| Power Supply Rejection Ratio (PSRR) | 92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00004μA |
| Input Capacitance | 5.5pF |
| Input Offset Current-Max (IIO) | 0.0005μA |
| Input Voltage Noise Density | 16nV/sqrt Hz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4000-2ARMZ-RL Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case which makes it easy for the consumer to handle. A J-FET-type buffer amplifier is shown here. A Tape & Reel (TR) case is used to deliver the buffer op amp. During the past two weeks, there have been close to 8 terminations. Linear amplifier has a total of 8 pins. Please take in mind that op amp should be run at 5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. There are 8 pins on this chip. As far as the input offset voltage is concerned, linear amplifier rates at 1.7mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~125°C. As long as the supply current of the chip does not exceed 3.3mA, this op amp ic can operate. There should be no change in the voltage gain. On the buffer amps, there are 2 channels that can be used. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. Linear amplifier has a quiescent current of 1.65mA.
ADA4000-2ARMZ-RL Features
8 Pins
supply voltage of 5V
114dB voltage gain
ADA4000-2ARMZ-RL Applications
There are a lot of Analog Devices Inc. ADA4000-2ARMZ-RL Instrumentational OP Amps applications.
- Precision measurement
- Medical imaging
- Ultrasound transducers
- Portable media players
- Vehicle electronics
- Comparator
- pH (acidity)
- Weighing systems
- Division circuits
- Logarithmic operation circuits
