ADA4004-4ACPZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | iPolar® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADA4004 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-5/+-15V |
| Number of Channels | 4 |
| Operating Supply Current | 8.8mA |
| Quiescent Current | 2.2mA |
| Slew Rate | 2.7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 113 dB |
| Current - Input Bias | 40nA |
| Voltage - Supply, Single/Dual (±) | 10V~36V ±5V~18V |
| Output Current per Channel | 10mA |
| Input Offset Voltage (Vos) | 125μV |
| Bandwidth | 12MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 12000 kHz |
| Voltage Gain | 112.04dB |
| Power Supply Rejection Ratio (PSRR) | 118dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 40μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.09μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Voltage Noise Density | 1.8nV/sqrt Hz |
| Height Seated (Max) | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4004-4ACPZ-R7 Overview
Packaging for the buffer amplifier is in the form of a 16-VQFN Exposed Pad, CSP case. Buffer amps of this type are called General Purpose-types. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be 16 terminations in the next few months. The total number of pins on linear amplifier is 16. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. There are 16 pins on this chip. With regard to input offset voltage, instrumentation amplifier is rated at 125μV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. This op amp can operate from a supply current at 8.8mA. There should be no change in the voltage gain at 112.04dB. On the buffer amps, there are 4 channels that can be used. As a result of this, the buffer amplifier is packed in TAPE AND REEL. iPolar? corresponds to the op amp's series. The quiescent current is 2.2mA.
ADA4004-4ACPZ-R7 Features
16 Pins
supply voltage of 5V
112.04dB voltage gain
ADA4004-4ACPZ-R7 Applications
There are a lot of Analog Devices Inc. ADA4004-4ACPZ-R7 Instrumentational OP Amps applications.
- Comparator
- Multiplication circuits
- Automatic control
- Band-stop filter
- Biopotential
- Weak signal detection
- Portable electronic products powered by batteries
- High gain DC amplifier
- single/dual op amp sum and difference circuits
- Exponential operation circuits
