ADA4310-1ACPZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 6V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADA4310 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 9V |
| Number of Channels | 2 |
| Operating Supply Current | 11.2mA |
| Nominal Supply Current | 11.2mA |
| Slew Rate | 820V/μs |
| Amplifier Type | Current Feedback |
| Common Mode Rejection Ratio | -62 dB |
| Current - Input Bias | 6μA |
| Voltage - Supply, Single/Dual (±) | 5V~12V ±2.5V~6V |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 190MHz |
| Gain Bandwidth Product | 190MHz |
| Neg Supply Voltage-Nom (Vsup) | -6V |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Low-Bias | NO |
| Micropower | NO |
| Programmable Power | NO |
| Dual Supply Voltage | 5V |
| Power | YES |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4310-1ACPZ-R7 Overview
Op amp is packaged in 16-VQFN Exposed Pad, CSP case. A Current Feedback-type buffer amplifier is shown here. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. There have been a total of 16 terminations over the past year. A total of 16 pins are attached to buffer op amp. Please take in mind that op amp should be run at 6V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. The op amp ic has an array of 16 pins on it. With regard to input offset voltage, instrumentation amplifier is rated at 1mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. With regard to operating temperature, this op amp functions well at -40°C~85°C. In order for this instrumentation amplifier to operate, the supply current needs to be between 11.2mA and 10 . As far as the device is concerned, buffer amplifier has 2 channels. The operating supply voltage of instrumentation amplifier is rated 9V voltage. It is used TAPE AND REEL to pack the op amps.
ADA4310-1ACPZ-R7 Features
16 Pins
supply voltage of 6V
ADA4310-1ACPZ-R7 Applications
There are a lot of Analog Devices Inc. ADA4310-1ACPZ-R7 Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Instrumentation
- pH (acidity)
- Micro signal measurement
- Video amplifiers
- Automation control systems
- Hand-held batteries
- PDA
- Test and measurement instruments
- Television
