ADA4610-2ARMZ-RL
| Parameters | |
|---|---|
| Input Voltage Noise Density | 14nV/sqrt Hz |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADA4610 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | +-4.5/+-15/9/30V |
| Number of Channels | 2 |
| Operating Supply Current | 3mA |
| Quiescent Current | 1.6mA |
| Supply Current-Max | 4mA |
| Slew Rate | 61V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 115 dB |
| Current - Input Bias | 5pA |
| Voltage - Supply, Single/Dual (±) | ±4.5V~15V |
| Output Current per Channel | 79mA |
| Input Offset Voltage (Vos) | 400μV |
| Gain Bandwidth Product | 16.3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 15400 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.0015μA |
| Power Supply Rejection Ratio (PSRR) | 125dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| -3db Bandwidth | 9.5MHz |
ADA4610-2ARMZ-RL Overview
There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case package that contains the instrumentation amplifiers. An op amp of this type is a J-FET-type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins on it. Please take in mind that op amp should be run at 5V. In order to be more specific, this instrumentation amplifier is one of the types of Operational Amplifier devices. It has 8 pins that make up the linear amplifier. There is an input offset voltage of 400μV for this buffer op amp. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. With regard to operating temperature, this op amp functions well at -40°C~125°C. As long as the supply current of the chip does not exceed 3mA, this op amp ic can operate. There should be no change in the voltage gain at 100dB. 2 channels are available on the instrumentation amplifier. One of its many advantages is that buffer op amp outputs Rail-to-Rail signals. TAPE AND REEL is adopted to pack the instrumentation amplifier. There is a quiescent current of 1.6mA in this operational amplifier circuit.
ADA4610-2ARMZ-RL Features
8 Pins
supply voltage of 5V
100dB voltage gain
Output Type: Rail-to-Rail
ADA4610-2ARMZ-RL Applications
There are a lot of Analog Devices Inc. ADA4610-2ARMZ-RL Instrumentational OP Amps applications.
- Tablets
- Video data acquisition
- Exponential operation circuits
- Portable docking station
- Comparator
- PDA
- Television
- Proportional counter tubes
- Precision measurement
- Signal amplification
