ADA4637-1ACPZ-R2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADA4637 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 7mA |
| Quiescent Current | 7mA |
| Slew Rate | 170V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 106 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 79.9MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 79900 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Power Supply Rejection Ratio (PSRR) | 108dB |
| Low-Offset | YES |
| Frequency Compensation | YES AVCL>=5 |
| Supply Voltage Limit-Max | 36V |
| Voltage - Input Offset | 120μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000005μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -36V |
| Input Voltage Noise Density | 16.5nV/sqrt Hz |
| Height | 900μm |
| Length | 3.25mm |
| Width | 3.25mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4637-1ACPZ-R2 Overview
Packaged in a 8-WFDFN Exposed Pad, CSP case, the buffer op amp is ready to use. A J-FET-type buffer amplifier is shown here. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. There have been a total of 8 terminations over the past year. A total of 8 pins are attached to buffer op amp. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 8 pins are included on the operational amplifiers. There is an input offset voltage of 200μV for this buffer op amp. This electronic part is recommended for mounting type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureUsing an 7mA supply current, this operational amplifier ics can be operated. 120dB should remain the voltage gain. Buffer op amp is equipped with 1 channels on the device. It is used TAPE AND REEL to pack the op amps. There is an 7mA quiescent current in linear amplifier.
ADA4637-1ACPZ-R2 Features
8 Pins
supply voltage of 15V
120dB voltage gain
ADA4637-1ACPZ-R2 Applications
There are a lot of Analog Devices Inc. ADA4637-1ACPZ-R2 Instrumentational OP Amps applications.
- Strain gauges
- PDA
- Multimedia playback equipment
- Micro signal measurement
- ECG equipment
- Vehicle electronics
- Scintillation detectors
- Digital cameras
- Portable media players
- Computer workstations
