ADA4691-2ACPZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN, CSP |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADA4691 |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Operating Supply Current | 180μA |
| Quiescent Current | 180μA |
| Slew Rate | 1.3V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 98 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.5V |
| Output Current per Channel | 55mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Bandwidth | 3.6MHz |
| Unity Gain BW-Nom | 3600 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00036μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Settling Time | 1.5 μs |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Input Capacitance | 7pF |
| Input Voltage Noise Density | 16nV/sqrt Hz |
| Height Seated (Max) | 0.6mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4691-2ACPZ-R7 Overview
There is a 10-UFQFN, CSP case in which the instrumentation amplifier is packaged. Op amps are Voltage Feedback types of amplifier on the chip. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. It is estimated that there will be 10 terminations in the next few months. The pins on this board total to 10 in total. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. It should be noted that this type of buffer amplifier is exactly what is known as a Operational Amplifier device. A total of 10 pins are present on the instrumentation amplifier. Regarding input offset voltage, op amp rates 2.5mV. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. An 180μA volt supply current is needed for this linear amplifier to operate. 110dB should remain the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. The operating supply voltage of the buffer op amp is rated at 3V. It is used TAPE AND REEL to pack the op amps. 180μA quiescent currents are flowing through buffer op amp.
ADA4691-2ACPZ-R7 Features
10 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
ADA4691-2ACPZ-R7 Applications
There are a lot of Analog Devices Inc. ADA4691-2ACPZ-R7 Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Automation control systems
- Weak signal detection
- Weighing systems
- PDA
- Ultrasound transducers
- Subtraction operation circuits
- Strain gauges
- Voltage regulation circuit
- Scintillation detectors
