ADA4692-2ARZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADA4692 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Operating Supply Current | 360μA |
| Quiescent Current | 180μA |
| Slew Rate | 1.3V/μs |
| Amplifier Type | Voltage Feedback |
| Common Mode Rejection Ratio | 98 dB |
| Current - Input Bias | 0.5pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.5V |
| Output Current per Channel | 55mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 3.6MHz |
| Unity Gain BW-Nom | 3600 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.00036μA |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Settling Time | 1.5 μs |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.000005μA |
| Programmable Power | NO |
| Input Capacitance | 7pF |
| Input Voltage Noise Density | 16nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4692-2ARZ Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. A Voltage Feedback-type buffer amplifier is shown here. A Tube case is used to deliver the buffer op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. 8 pins are included on the operational amplifiers. In terms of the input offset voltage, instrumentation amplifier rates at 500μV. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . A supply current of 360μA can be used to operate this linear amplifier. Voltage gain should remain at 110dB. Op amp ic has 2 channels. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of instrumentation amplifier is rated 3V voltage. Buffer amplifier has a quiescent current of 180μA.
ADA4692-2ARZ Features
8 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
ADA4692-2ARZ Applications
There are a lot of Analog Devices Inc. ADA4692-2ARZ Instrumentational OP Amps applications.
- Ultrasound transducers
- High speed sample
- Blood pressure sensors
- Oscilloscopes
- Fission chambers
- Automatic control
- High/low-pass filter circuit
- High gain DC amplifier
- Band-stop filter
- Band-pass filter
