ADA4932-1YCPZ-R2
| Parameters | |
|---|---|
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-VFQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 16MOhm |
| Terminal Finish | Matte Tin (Sn) |
| Technology | BIPOLAR |
| Terminal Position | QUAD |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | ADA4932 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Operating Supply Current | 9.6mA |
| Nominal Supply Current | 9.6mA |
| Slew Rate | 2800V/μs |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 87 dB |
| Current - Input Bias | 2.5μA |
| Voltage - Supply, Single/Dual (±) | 3V~11V ±1.5V~5.5V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2.2mV |
| Bandwidth | 560MHz |
| Differential Output | YES |
| Voltage Gain | 66dB |
| Power Supply Rejection Ratio (PSRR) | 84dB |
| Output Polarity | COMPLEMENTARY |
| Voltage - Input Offset | 500μV |
| Interface IC Type | LINE DRIVER |
| Driver Number of Bits | 1 |
| Dual Supply Voltage | 5V |
| Interface Standard | GENERAL PURPOSE |
| Negative Supply Voltage-Nom | -5V |
| Out Swing-Min | 3.2 V |
| Height | 830μm |
| Length | 3mm |
| Width | 3mm |
ADA4932-1YCPZ-R2 Overview
Packaged in a 16-VFQFN Exposed Pad, CSP case, the buffer op amp is ready to use. Differential-type instrumentation amplifiers are used in this application. A Tape & Reel (TR) case is used for delivering the op amp. It is estimated that there will be 16 terminations in the next few months. In this case, there are 16 pins on the board. Please take in mind that op amp should be run at 5V. The op amp ic has an array of 16 pins on it. As far as the input offset voltage is concerned, linear amplifier rates at 2.2mV. This electrical part should be mounted using type Surface Mount. The buffer amplifier functions well at -40°C~105°C as far as operating temperature is concerned. An 9.6mA volt supply current is needed for this linear amplifier to operate. Maintain 66dB as the voltage gain. Buffer op amp is equipped with 1 channels on the device. The operating supply voltage of instrumentation amplifier is rated 9V voltage. It is recommended to keep the buffer amps resistance within the range of 16MOhm. The interface IC of the electronic part is classified as LINE DRIVER.
ADA4932-1YCPZ-R2 Features
16 Pins
supply voltage of 5V
66dB voltage gain
Resistance of 16MOhm
ADA4932-1YCPZ-R2 Applications
There are a lot of Analog Devices Inc. ADA4932-1YCPZ-R2 Instrumentational OP Amps applications.
- Broadcasting
- Mobile phone
- Signal amplification
- Thermocouples
- Semiconductor detectors
- Communication device
- Ultrasound transducers
- Industrial control system
- Multimedia playback equipment
- Automotive sensors
