ADG1201BRJZ-R2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG1201 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Nominal Supply Current | 30mA |
| Max Supply Current | 100mA |
| Turn On Delay Time | 230 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±5V~16.5V |
| Turn-Off Delay Time | 141 ns |
| Max Dual Supply Voltage | 16.5V |
| -3db Bandwidth | 660MHz |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3.3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 170ns, 105ns |
| Charge Injection | -0.8pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Drain to Source Resistance | 200Ohm |
| Normal Position | NC |
| Height | 1.3mm |
| Length | 2.9mm |
| Width | 1.6mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1201BRJZ-R2 Overview
Shipping overseas is convenient due to the electrical component's packing in SOT-23-6. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~125°C TA. There are 6 terminations totally. Electronic part bodies are injected with 6 pins. Multiplexers built on a SPST - NO switching circuit are built. Search with ADG1201 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 200Ohm. Datasheets for functions of 6 pins are available. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16.5V. The lowest voltage the electronic part should receive is 5V. A voltage higher than 100mA may cause damage to the switch multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 16.5V. When using dual power supplies, you should attach at least 5V. 12V operating voltages are supported by the electronic component. Among the inputs that can be operated are the 1 inputs. A Drain to Source resistance of 200Ohm is shown for this electronic part.
ADG1201BRJZ-R2 Features
Switch Circuit: SPST - NO
-3db Bandwidth: 660MHz
Drain-to-Source resistance: 200Ohm
ADG1201BRJZ-R2 Applications
There are a lot of Analog Devices Inc. ADG1201BRJZ-R2 Analog Switches & Multiplexers ICs applications.
- Automotive applications
- Low-Voltage
- ATM
- High speed data transmission line cards
- Relay replacements
- New designs requiring multiplexer functions
- Battery Powered Systems
- Cross Connects
- Isolation
- Multiplexers
