ADG1201BRJZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG1201 |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 60μA |
| Max Supply Current | 95μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 170 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±5V~16.5V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 105 ns |
| Max Dual Supply Voltage | 16.5V |
| -3db Bandwidth | 660MHz |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3.3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 170ns, 105ns |
| Charge Injection | -0.8pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Normal Position | NC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1201BRJZ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOT-23-6. High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~125°C TA. In total, there have been 6 terminations. 6 pins are injected to the electronic part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Look for analog switch ic variants by searching with ADG1201. In this multiplexer, the internal resistance is 200Ohm. The functions of 6 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 16.5V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 5V. An operating current of 60μA would be sufficient for this switch device. A digital multiplexer may suffer damage if voltage is applied above 95μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 16.5V. If you are using a dual power supply, you should attach at least 5V. Operating voltages of 12V are compatible with the electrical part. There are 1 inputs to be operated.
ADG1201BRJZ-REEL7 Features
Switch Circuit: SPST - NO
60μA Supply Current
-3db Bandwidth: 660MHz
ADG1201BRJZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1201BRJZ-REEL7 Analog Switches & Multiplexers ICs applications.
- HDTV
- Digital Cross-Connects
- Avionics
- Low-Voltage
- Access Concentrators
- Modems
- PBX interfaces
- High reliability control systems
- Residential Gateways, Home Gateway/Router
- Power routing
