Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-VQFN Exposed Pad, CSP |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
200Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
4.7mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG1208 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
12V |
Number of Channels |
8 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
5V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Nominal Supply Current |
220μA |
Power Dissipation |
4.7mW |
Voltage - Supply, Single/Dual (±) |
5V~16.5V ±5V~16.5V |
Bandwidth |
550MHz |
Supply Current-Max (Isup) |
0.33mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
83 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
200Ohm |
Min Dual Supply Voltage |
5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
85 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
1.5pF 7pF |
On-state Resistance Match-Nom |
3.5Ohm |
Switch Time (Ton, Toff) (Max) |
95ns, 100ns |
Charge Injection |
0.4pC |
Channel-to-Channel Matching (ΔRon) |
3.5 Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Length |
4mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG1208YCPZ-REEL7 Overview
The electrical component comes in 16-VQFN Exposed Pad, CSP packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Operating temperature around -40°C~125°C TA extended. A total of 16 terminations have been recorded. By its 8 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A total of 16 pins are injected into the body of the electronic part. A 1 circuit is present in this switch device. Try searching for the analog switch ic with ADG1208 if you are looking for variants. Analog switches have 200Ohm internal resistance. Datasheets for 16 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 16.5V to a switch device. 5V is the lowest voltage that should be fed to the electronic electronic part. For this switch, a dual supply voltage is feasible, but it must not exceed 16.5VA dual power supply should have at least 5V voltage attached. With a SINGLE-ENDED MULTIPLEXER analog IC integrated into the board. There is a voltage range of 12V operating voltages for the electrical part. The transfer of data can be performed over 550MHz bandwidths.
ADG1208YCPZ-REEL7 Features
8 Channels
Bandwidth: 550MHz
ADG1208YCPZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1208YCPZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Audio signal routing
- Medical systems
- Public switching systems
- Audio and video signal routing
- Microwave transmission systems
- FTTH
- PBXs
- Transmit
- Audio/video switches