ADG1211YCPZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 190Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 150μW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG1211 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Test Frequency | 1MHz |
| Operating Supply Current | 220μA |
| Power Dissipation | 150μW |
| Max Supply Current | 380μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±4.5V~16.5V |
| Supply Type | Dual, Single |
| Bandwidth | 700MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 115 ns |
| Max Dual Supply Voltage | 16.5V |
| -3db Bandwidth | 1GHz |
| On-State Resistance (Max) | 190Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 1.1pF 1.2pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 115ns |
| Charge Injection | -0.3pC |
| Channel-to-Channel Matching (ΔRon) | 2.5 Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 0.9mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1211YCPZ-REEL7 Overview
Packed in 16-WFQFN Exposed Pad, CSP, the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~125°C TA are extended for operation. There are 16 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. A SPST - NC switching circuit is used to build these analog multiplexers. Circuits number 1 make up this analogue multiplexer. Try searching for the analog switch ic with ADG1211 if you are looking for variants. This digital multiplexer has 190Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 16.5V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 5V. 220μA current would be enough for this multiplexer to operate. Put voltage above 380μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 16.5V. If you are using dual power supplies, you should attach at least 4.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. There is a voltage range of 12V operating voltages for the electrical part. A 4 input needs to be operated. There are 700MHz bandwidths for data transfer.
ADG1211YCPZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
220μA Supply Current
-3db Bandwidth: 1GHz
Bandwidth: 700MHz
ADG1211YCPZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1211YCPZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- 65 V DACs
- Fault Tolerant Systems
- PBX interfaces
- Mechanical reed relay replacement
- Cellular phones
- Remote wireless modules
- Channelized and Unchannelized DS3 applications
- Communication systems
- Data switching
