ADG1211YRUZ

130ns, 115ns SPST - NC 190Ohm Analog Switches BREAK-BEFORE-MAKE ADG1211 16 Pins 100pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG1211YRUZ
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 738
Description: 130ns, 115ns SPST - NC 190Ohm Analog Switches BREAK-BEFORE-MAKE ADG1211 16 Pins 100pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 1 week ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	190Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	150μW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG1211
Pin Count	16
Operating Supply Voltage	12V
Polarity	Inverting, Non-Inverting
Number of Channels	1
Interface	Parallel
Number of Circuits	1
Max Supply Voltage	16.5V
Min Supply Voltage	5V
Test Frequency	1MHz
Operating Supply Current	220μA
Nominal Supply Current	320μA
Power Dissipation	150μW
Max Supply Current	380μA
Throw Configuration	SPST
Turn On Delay Time	130 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	5V~16.5V ±4.5V~16.5V
Supply Type	Dual, Single
Bandwidth	1 GHz
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	115 ns
Max Dual Supply Voltage	16.5V
On-State Resistance (Max)	190Ohm
Min Dual Supply Voltage	4.5V
High Level Output Current	25mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	75 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	1.1pF 1.2pF
On-state Resistance Match-Nom	5Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	130ns, 115ns
Charge Injection	-0.3pC
Channel-to-Channel Matching (ΔRon)	2.5 Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	120Ohm
Height	1.05mm
Length	5mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG1211YRUZ Overview

Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tube is used. Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Temperatures around -40°C~125°C TA are extended for operation. The total number of terminations is 16. As a result of its 1 channels, this electronic component provides high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Unlike digital switches, these are based on SPST - NC switching circuits. Circuits number 1 make up this analogue multiplexer. ADG1211 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 190Ohm. Please refer to the datasheets for 16 pins functions. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 16.5V. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 5V should be applied to the electronic component. The switch device would be able to operate with 220μA current. If put voltage greater than 380μA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 16.5V. For dual power supplies, a voltage of at least 4.5V should be attached. This electrical part is compatible with 12V operating voltages. The 4 inputs need to be operated in order to work. In 1 GHz-bandwidths, data can be transferred. There is 120Ohm resistance between Drain and Source for this electronic part.