ADG1211YRUZ-REEL
| Parameters | |
|---|---|
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 12V |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Test Frequency | 1MHz |
| Operating Supply Current | 220μA |
| Power Dissipation | 150μW |
| Max Supply Current | 380μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±4.5V~16.5V |
| Supply Type | Dual, Single |
| Bandwidth | 700MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 115 ns |
| Max Dual Supply Voltage | 16.5V |
| -3db Bandwidth | 1GHz |
| On-State Resistance (Max) | 190Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 1.1pF 1.2pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 115ns |
| Charge Injection | -0.3pC |
| Channel-to-Channel Matching (ΔRon) | 2.5 Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 190Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 150μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG1211 |
ADG1211YRUZ-REEL Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). This analog switch is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~125°C TA. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. It is injected into the electrical part body with 16 pins. SPST - NC switching circuits are used in these analog switch ics. This multiplexer is composed of 1 circuits. Search with ADG1211 if you are looking for analog multiplexer variants. An switch multiplexer with 190Ohm internal resistance has a value of 190Ohm. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 16.5V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. 5V should be the lowest voltage fed to the electronic component. 220μA current would be enough for this multiplexer to operate. If you put voltage higher than 380μA on the digital multiplexer, damage may occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 16.5V. When using dual power supplies, you should attach at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages of 12V are compatible with the electrical part. In 700MHz-bandwidths, data can be transferred. It is capable of carrying out 4-bit operation.
ADG1211YRUZ-REEL Features
1 Channels
Switch Circuit: SPST - NC
220μA Supply Current
-3db Bandwidth: 1GHz
Bandwidth: 700MHz
4-Bit
ADG1211YRUZ-REEL Applications
There are a lot of Analog Devices Inc. ADG1211YRUZ-REEL Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Optical Applications
- Fault Tolerant Systems
- Relay replacements
- Sample-and-hold systems
- Fiber In The Loop (FITL)
- Cellular phones
- Automatic test equipment
- Private Branch Exchange (PBX)
- Channelized and Unchannelized DS3 applications
