Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Supplier Device Package |
16-TSSOP |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Resistance |
190Ohm |
Max Operating Temperature |
125°C |
Min Operating Temperature |
-40°C |
Max Power Dissipation |
150μW |
Base Part Number |
ADG1212 |
Number of Outputs |
4 |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Interface |
Parallel |
Number of Circuits |
4 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
5V |
Test Frequency |
1MHz |
Operating Supply Current |
220μA |
Power Dissipation |
150μW |
Max Supply Current |
380μA |
Number of Bits |
4 |
Throw Configuration |
SPST |
Turn On Delay Time |
130 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
5V~16.5V ±4.5V~16.5V |
Supply Type |
Dual, Single |
Bandwidth |
700MHz |
Turn-Off Delay Time |
115 ns |
Max Dual Supply Voltage |
16.5V |
-3db Bandwidth |
1GHz |
On-State Resistance (Max) |
190Ohm |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
1.1pF 1.2pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
130ns, 115ns |
Charge Injection |
-0.3pC |
Channel-to-Channel Matching (ΔRon) |
2.5Ohm |
Crosstalk |
-90dB @ 1MHz |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG1212YRUZ-REEL7 Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~125°C TA. This electronic part offers high-quality output due to its 4 channels. Circuits based on SPST - NO switching are used to construct these analog switch ics. This multiplexer is composed of 4 circuits. Search with ADG1212 if you are looking for analog multiplexer variants. This digital multiplexer has 190Ohm internal resistance. Datasheets for 16 pin functions are available upon request. In a normalsituation, users should not supply the switches with voltage higher than 16.5V. A cost-effective Dual, Single supply type analogue multiplexer. There should be 5V voltage fed to the electrical part below 5V. It would be sufficient to run this analogue multiplexer with 220μA current. If you put voltage higher than 380μA on the digital multiplexer, damage may occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 16.5V. In the case of dual power supplies, you should connect at least 4.5V. 12V operating voltages are supported by the electronic component. The electrical component supports 4 inputs. This switch operates within the bandwidth of 700MHz. The switches should not operate in an environment where the temperature is higher than 125°C. Multiplexer ics with 4 outputs are available. There is a 16-TSSOP package available from suppliers. It is capable of carrying out 4-bit operation.
ADG1212YRUZ-REEL7 Features
4 Channels
Switch Circuit: SPST - NO
220μA Supply Current
-3db Bandwidth: 1GHz
Bandwidth: 700MHz
4-Bit
ADG1212YRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1212YRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Public switching systems
- Data Acquisition Systems
- Routers
- Avionics
- E1 Multiplexer
- Frame Relay Equipment
- Microprocessor Controlled Analog Systems
- DSLAMs
- Industrial control systems
- Ultrasound