banner_page

ADG1222BRMZ-REEL7

130ns, 105ns SPST - NC 200Ohm Analog Switches BREAK-BEFORE-MAKE ADG1222 10 Pins 100pA 15V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)


  • Manufacturer: Analog Devices Inc.
  • Nocochips NO: 84-ADG1222BRMZ-REEL7
  • Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
  • Datasheet: PDF
  • Stock: 405
  • Description: 130ns, 105ns SPST - NC 200Ohm Analog Switches BREAK-BEFORE-MAKE ADG1222 10 Pins 100pA 15V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status PRODUCTION (Last Updated: 1 week ago)
Mounting Type Surface Mount
Package / Case 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Surface Mount YES
Number of Pins 10
Operating Temperature -40°C~125°C TA
Packaging Tape & Reel (TR)
JESD-609 Code e3
Pbfree Code no
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 10
ECCN Code EAR99
Resistance 200Ohm
Terminal Finish Matte Tin (Sn)
Subcategory Multiplexer or Switches
Max Power Dissipation 2.3mW
Technology CMOS
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 15V
Terminal Pitch 0.5mm
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number ADG1222
Output SEPARATE OUTPUT
Pin Count 10
Operating Supply Voltage 12V
Number of Channels 1
Interface Parallel
Number of Circuits 2
Max Supply Voltage 16.5V
Min Supply Voltage 5V
Test Frequency 1MHz
Operating Supply Current 140μA
Power Dissipation 2.9mW
Max Supply Current 190μA
Throw Configuration SPST
Turn On Delay Time 170 ns
Voltage - Supply, Single/Dual (±) 5V~16.5V ±5V~16.5V
Supply Type Dual, Single
Bandwidth 960MHz
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 105 ns
Max Dual Supply Voltage 16.5V
On-State Resistance (Max) 200Ohm
Min Dual Supply Voltage 5V
Dual Supply Voltage 15V
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 75 dB
Current - Leakage (IS(off)) (Max) 100pA
Channel Capacitance (CS(off), CD(off)) 2.2pF 2.2pF
On-state Resistance Match-Nom 2.5Ohm
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 130ns, 105ns
Charge Injection 0.1pC
Channel-to-Channel Matching (ΔRon) 2.5 Ω
Crosstalk -90dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-off Time-Max 140ns
Height Seated (Max) 1.1mm
Length 3mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Contains Lead

ADG1222BRMZ-REEL7 Overview


The electronic part can be shipped overseas conveniently because it is packaged in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, 10 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 10 series that this electronic component is included. These analog multiplexers are built based on SPST - NC switching circuits. The multiplexer consists of 2 circuits. Try searching with ADG1222 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 200Ohm. Datasheets for functions of 10 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 16.5V to a switch device. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage fed to the electronic component should be 5V. 140μA current would be enough for this multiplexer to operate. If put voltage greater than 190μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 16.5V. It is recommended that you attach at least 5V to your dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. The electronic component can function from 12V. There are 960MHz bandwidths for data transfer.

ADG1222BRMZ-REEL7 Features


1 Channels
Switch Circuit: SPST - NC
140μA Supply Current
Bandwidth: 960MHz

ADG1222BRMZ-REEL7 Applications


There are a lot of Analog Devices Inc. ADG1222BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.

  • Industrial and process control systems
  • Cable Modem
  • Industrial control systems
  • Communication systems
  • PBX interfaces
  • Isolation
  • E1 Multiplexer
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • ISDN NT1/TA
  • Intelligent PBX

Write a review

Note: HTML is not translated!
    Bad           Good