Parameters |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
200Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
2.3mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG1223 |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Operating Supply Voltage |
12V |
Number of Channels |
1 |
Interface |
Parallel |
Number of Circuits |
2 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
5V |
Test Frequency |
1MHz |
Power Dissipation |
2.9mW |
Max Supply Current |
190μA |
Turn On Delay Time |
170 ns |
Voltage - Supply, Single/Dual (±) |
5V~16.5V ±5V~16.5V |
Supply Type |
Dual, Single |
Bandwidth |
960MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
105 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
200Ohm |
Min Dual Supply Voltage |
5V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
2.2pF 2.2pF |
On-state Resistance Match-Nom |
2.5Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
130ns, 105ns |
Charge Injection |
0.1pC |
Channel-to-Channel Matching (ΔRon) |
2.5 Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
140ns |
Drain to Source Resistance |
120Ohm |
Height |
850μm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
ADG1223BRMZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~125°C TA are extended for operation. Total terminations are 10. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. As part of its design, the 10 series is equipped with this electronic component. A SPST - NO/NC switching circuit is used to build these analog multiplexers. There are 2 circuits in this multiplexer. Try searching for ADG1223 variants of the analog switch ic. A 200Ohm internal resistance characterizes this multiplexer. To find out what the functions of 10 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 16.5V to a switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 5V should be the lowest voltage fed to the electronic component. Putting voltage greater than 190μA on the multiplexer may cause damage. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 5V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. 12V operating voltages can be used with this electrical part. There are various bandwidths available for data transfer. There is 120Ohm resistance between the Drain and Source on this part.
ADG1223BRMZ Features
1 Channels
Switch Circuit: SPST - NO/NC
Bandwidth: 960MHz
Drain-to-Source resistance: 120Ohm
ADG1223BRMZ Applications
There are a lot of Analog Devices Inc. ADG1223BRMZ Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Multi-Line E1 Interface Cards
- Modems
- Avionics test equipment
- PDAs
- Cable PC
- New designs requiring multiplexer functions
- Microprocessor controlled systems
- Fiber In The Loop (FITL)