ADG1236YCPZ-500RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFQFN Exposed Pad, CSP |
| Number of Pins | 12 |
| Supplier Device Package | 12-LFCSP-WQ (3x3) |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Resistance | 190Ohm |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 3.5mW |
| Base Part Number | ADG1236 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 12V |
| Number of Channels | 2 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Test Frequency | 1MHz |
| Nominal Supply Current | 230μA |
| Power Dissipation | 3.5mW |
| Max Supply Current | 230μA |
| Number of Bits | 2 |
| Throw Configuration | SPDT |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 2 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Bandwidth | 1 GHz |
| Turn-Off Delay Time | 90 ns |
| Max Dual Supply Voltage | 16.5V |
| -3db Bandwidth | 1GHz |
| On-State Resistance (Max) | 190Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 1.6pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 90ns |
| Charge Injection | -1pC |
| Channel-to-Channel Matching (ΔRon) | 3.5Ohm |
| Crosstalk | -85dB @ 1MHz |
| Height | 950μm |
| Length | 3mm |
| Width | 2.75mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1236YCPZ-500RL7 Overview
Shipping overseas is convenient with the electronic component packed in 12-WFQFN Exposed Pad, CSP. The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. By its 2 channels, the electronic component provides high-quality output. A SPDT switching circuit is used to build these analog multiplexers. There are 2 circuits in this switch device. Try searching for ADG1236 variants of the analog switch ic. Analog switches have 190Ohm internal resistance. Please refer to the datasheets for 12 pins functions. In normalcircumstances, users should not exceed 16.5V volts for the multiplexer. Analog switch ics with Dual, Single supply type are cost-effective. 5V should be the lowest voltage fed to the electronic component. A digital multiplexer may suffer damage if voltage is applied above 230μA. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 5V to your dual power supply. This electrical part is compatible with 12V operating voltages. Operating the 2 inputs requires 2 inputs. 1 GHz-bandwidths can be used to transfer data between multiplexers. It is not recommended to operate the switches in an environment with a temperature higher than 125°C. In this digital multiplexer, there are 4 outputs. Suppliers offer a 12-LFCSP-WQ (3x3) package. It can conduct 2-bit signals.
ADG1236YCPZ-500RL7 Features
2 Channels
Switch Circuit: SPDT
-3db Bandwidth: 1GHz
Bandwidth: 1 GHz
2-Bit
ADG1236YCPZ-500RL7 Applications
There are a lot of Analog Devices Inc. ADG1236YCPZ-500RL7 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Avionics test equipment
- Audio and video switching
- Low-Voltage
- Relay Replacement
- Fiber In The Loop (FITL)
- Modems
- High speed data transmission line cards
- Communication systems
- Audio/video switches
