ADG1308BRUZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 210Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG1308 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 220μA |
| Throw Configuration | DPST |
| Propagation Delay | 130 ns |
| Turn On Delay Time | 110 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~16.5V ±5V~16.5V |
| Supply Type | Dual, Single |
| Bandwidth | 500MHz |
| Supply Current-Max (Isup) | 2mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 210Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF 20pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 100ns, 100ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1308BRUZ-REEL7 Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 8:1. Around -40°C~105°C TA is the extended operating temperature. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 8 channels. An 15V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 16 pins. It consists of 1 circuits. Try searching for the analog switch ic with ADG1308 if you are looking for variants. The internal resistance of this digital multiplexer is 210Ohm. Datasheets for 16 pin functions are available upon request. Multiplexers should not be powered above 16.5V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 5V. The switch device would be able to operate with 220μA current. There is no problem with using dual supply voltage, but it should not exceed 16.5V. The voltage should be at least 5V if you are using dual power supplies. The electrical part can be operated at 15V voltage levels. The data can be transferred over a wide range of bandwidths, called 500MHz bandwidths.
ADG1308BRUZ-REEL7 Features
8 Channels
220μA Supply Current
Bandwidth: 500MHz
ADG1308BRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG1308BRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- SONET
- Digital cross connects (DSX-1)
- Modems
- Access Concentrators
- Video switching
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Medical systems
- Relay Replacement
- Avionics test equipment
