ADG1311YRUZ

125ns, 50ns SPST - NC 200Ohm Analog Switches BREAK-BEFORE-MAKE ADG1311 16 Pins 10nA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG1311YRUZ
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 288
Description: 125ns, 50ns SPST - NC 200Ohm Analog Switches BREAK-BEFORE-MAKE ADG1311 16 Pins 10nA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 4 weeks ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~105°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	200Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	4.8mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG1311
Pin Count	16
Operating Supply Voltage	12V
Polarity	Non-Inverting
Number of Channels	4
Interface	Parallel
Max Supply Voltage	16.5V
Min Supply Voltage	5V
Test Frequency	1MHz
Nominal Supply Current	320μA
Power Dissipation	4.8mW
Max Supply Current	380μA
Throw Configuration	SPST
Turn On Delay Time	125 ns
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Bandwidth	600MHz
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	50 ns
Max Dual Supply Voltage	16.5V
On-State Resistance (Max)	200Ohm
Min Dual Supply Voltage	5V
High Level Output Current	25mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	80 dB
Current - Leakage (IS(off)) (Max)	10nA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	5Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	125ns, 50ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	5 Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	180ns
Switch-off Time-Max	60ns
Drain to Source Resistance	130Ohm
Height	1.05mm
Length	5mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG1311YRUZ Overview

Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature around -40°C~105°C TA extended. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. There are 16 pins injected into the electronic part body. Unlike digital switches, these are based on SPST - NC switching circuits. Look for analog switch ic variants by searching with ADG1311. It has an internal resistance of 200Ohm. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 16.5V volts for the multiplexer. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 5V. If put voltage greater than 380μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 16.5V. The voltage should be at least 5V if you are using dual power supplies. A voltage of 12V can be used to operate the electronic component. In 600MHz-bandwidths, data can be transferred. Drain to Source resistance for this electronic component is 130Ohm.