ADG1311YRUZ-REEL7

125ns, 50ns SPST - NC 200Ohm Analog Switches BREAK-BEFORE-MAKE ADG1311 16 Pins 10nA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG1311YRUZ-REEL7
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 938
Description: 125ns, 50ns SPST - NC 200Ohm Analog Switches BREAK-BEFORE-MAKE ADG1311 16 Pins 10nA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 4 weeks ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~105°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	200Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	4.8mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG1311
Pin Count	16
Qualification Status	Not Qualified
Operating Supply Voltage	12V
Polarity	Non-Inverting
Number of Channels	4
Interface	Parallel
Max Supply Voltage	16.5V
Min Supply Voltage	5V
Test Frequency	1MHz
Operating Supply Current	220μA
Power Dissipation	4.8mW
Max Supply Current	380μA
Throw Configuration	SPST
Turn On Delay Time	125 ns
Supply Type	Dual, Single
Bandwidth	600MHz
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	50 ns
Max Dual Supply Voltage	16.5V
On-State Resistance (Max)	200Ohm
Min Dual Supply Voltage	5V
High Level Output Current	25mA
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	80 dB
Current - Leakage (IS(off)) (Max)	10nA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	5Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	125ns, 50ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	5 Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	180ns
Switch-off Time-Max	60ns
Voltage - Supply, Dual (V±)	±15V
Height Seated (Max)	1.2mm
Length	5mm
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG1311YRUZ-REEL7 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~105°C TA. 16 terminations have been made so far. A 4 channel electronic part produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 16 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. Look for analog switch ic variants by searching with ADG1311. Analog switches have 200Ohm internal resistance. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16.5V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 5V should be the lowest voltage fed to the electronic component. This multiplexer would work with 220μA current. A voltage higher than 380μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 16.5VA dual power supply should have at least 5V voltage attached. The electrical part can be operated at 12V voltage levels. The data can be transferred over a wide range of bandwidths, called 600MHz bandwidths.