ADG1334BRSZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~105°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 6.02mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG1334 |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Operating Supply Voltage | 12V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 5V |
| Test Frequency | 1MHz |
| Operating Supply Current | 260μA |
| Power Dissipation | 6.02mW |
| Max Supply Current | 400μA |
| Throw Configuration | SPDT |
| Turn On Delay Time | 130 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Bandwidth | 700MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 85 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 200Ohm |
| Min Dual Supply Voltage | 5V |
| High Level Output Current | 24mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 85ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 325Ohm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.75mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG1334BRSZ Overview
Due to its 20-SSOP (0.209, 5.30mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tube is used to provide high reliability. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~105°C TA. There are 20 terminations totally. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 20 pins are injected into the electrical part body. These analog multiplexers are built based on SPST - NO/NC switching circuits. ADG1334 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 200Ohm. Datasheets for 20 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 16.5V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 5V. This multiplexer would work with 260μA current. If you put voltage higher than 400μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 16.5V. The voltage should be at least 5V if you are using dual power supplies. There is a voltage range of 12V operating voltages for the electrical part. Operating the 4 inputs requires 4 inputs. 700MHz bandwidths enable data to be transferred. It has a Drain to Source resistance of 325Ohm ohms. A analog switch ics with 8 outputs is included.
ADG1334BRSZ Features
1 Channels
Switch Circuit: SPST - NO/NC
260μA Supply Current
Bandwidth: 700MHz
Drain-to-Source resistance: 325Ohm
ADG1334BRSZ Applications
There are a lot of Analog Devices Inc. ADG1334BRSZ Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- New designs requiring multiplexer functions
- High-Voltage
- Medical
- Mechanical reed relay replacement
- Microwave transmission systems
- Frame Relay Equipment
- Fault Tolerant Systems
- Digital access cross connects
- E1 Multiplexer
